Note: The RC drone and FPV Goggles will be sent in two parcels. ARRIS X-Speed 250B V3.0 is the latest version of ARRIS X-Speed. It is fully assemble, tuned and tested by the technician before leaving the factory. It comes with Raptor 390 Tower w/ 30A 4in1 ESC + F3 + OSD + PDB, ARRIS S2205 2300KV brushless motor, 5042 high efficiency 3 blade propeller, 1000TVL HD camera, 5.8g 200mw FPV TX and antenna, flysky FSi6 transmitter and 4S 1500mah lipo battery. Plug the battery, it will work.
On this tower, the pins connect the flight controller board and the ESC board, maximally decrease the interference caused by signal transmission. The Tower structure design could protect the ESC well during the flight. ESC is one of the most easily broken parts on the drones except the propellers. According to our experience, some of the ESC were damged by the propeller rotation or tree brunch cut after the damage when it installed on top of the motor arm. Some of the ESC were damaged due to the broken of the motor arm during the crash. For this tower, the esc integrated in the tower which installed in the middle of the quad frame, the ESCs can be protected quite well. Raptor 390 tower makes the assembling of the fpv racing drones more and more convenient, the wires tidy and concise. Using this tower, you just need to solder the 4 motor wries to the holes, so easy. The lower board integrated the 4in1 ESC, the power port is in the center, bulge a bit over. This could not only make the connecting wires more convenient, but also avoid to interrupt the esc output port on the two sides. The upper board F3 flight controller board integrated with the OSD. There is also 5V, 12V and BATV for powering the camera, video tx, LED and other euipements. Small size and light weight tower fit for all sizs of the quad, and make the center of gravity of the drone lower. The weight of the raptor 390 tower is only 22g, with two layers tower structure, the height is only 15.1mm. And there are two plates on the tower, one is 4in1 ESC, and the other is the FC flight controller. If some of the components on the tower damaged, you just need to change one plate of the tower.
NSK bearing: ARRIS S2205 2300KV adopts 0.2mm Japan inported stators, ultra hardness aerospace aluminum and precision cnd, which make the motor more effiency and prolong the working life. Low center design: The height of the ARRIS S2205 allows a lower center of gravity closer to the mounting point, with this, the drone can fly smoothly. Cooling system: The cooling system make the motor more air flow. Hollowed steel prop shaft: with this, you do not need to worry of damaging threads during crashes.
The digonal wheelbase of the ARRIS X250B frame is about 268mm , and the inner space between upper plate and lower plate is quite big. Customer can upgrade or do some modifications as you like. For example, you can install 6 inches propellers on it.
On the ARRIS X-Speed 250B V3.0, we abadoned the PCB board. Many customer reflects the capicator is easily took off, the PCB is easily damaged during the crash or caused the short out on the wire. The Raptor 390 Tower w/ 30A 4in1 ESC + F3 + OSD + PDB solved this problem perfectly. ARRIS X-Speed 250B comes with a high brightness LED. And you can change the color of the LED light through the DIP switches. 7 color for you to choose. ARRIS 5.8g 200mW 40-CH video TX pre-assembled. The ARRIS TS5823S transmitter packs 200mW of ultra clean 5.8GHz power in a micro sized video/audio transmitter! A must for those looking save size and weight while still getting good performance. The ARRIS TS5823S is transmitting a full range of 40 channels and only weighs 10g. It's perfect for a wide range of aircraft! With a goggle or monitor in hand, you can begin your FPV journey. FlySky FS-i6-M2 2.4GHz 6-Channel Transmitter with FS-iA6B receiver. Specifications: Channels: 6 Channels Model Type: fixed-wing/glider/helicopter RF range: 2.405-2.475Ghz Bandwidth: 500Khz Band: 142 RF Power: Less than 20 dBm 2.4G System: AFHDS 2A and AFHDS Code type: GFSK Sensitivity: 1024 Low voltage warning: Less than 4.2V DSC port: PS2; output: PPM Charger port: No ANT length: 26mm2 (dual antenna) Weight: 392g Power: 6V 1.5AA4 Display mode: Transflective STN positive type, 12864 dot matric VA7339mm, white backlight Size: 17489190mm Online update: yes Color: Black Certificate: CE0678, FCC. ARRIS X-Speed 250B has integrated with a remote controller battery warning buzzer , pilot can set the threshold (adjustable) according to CF parameter-adjustment software.
High safety ARRIS 4S 1500mah Lipo Battery. ARRIS 4S 1500mAh 50C lipo battery is specially designed for FPV racer.
The price of this battery is much higher than the similar batteries in the market, because we only sell top-quality batteries. As we all know, the low quality battery might have potential safety hazard, we will never tolerate such products. For ARRIS 4S 1500mah lipo battery, we have done UN38.3 test, 1.2M Drop test, MDS report for it, for the test report, you can check here. Package Includes: 1 x ARRIS X-Speed 250B Racing Quad Frame 1 x ARRIS EV800 FPV Goggles. 4 x ARRIS S2205 2300KV Brushless Motors (2CW + 2CCW).
1 x FPV Transmitter Antenna 1 x FlySky FS-i6-M2 Transmitter with FS-iA6B receiver 1 x LED. 1 x ARRIS 4S 1500mah Lipo Battery. Other Parts Required (Not Include): Battery Charger: Suggest IMAX B6 Mini.
The item "ARRIS X-Speed 250B V3 250 FPV Racing Drone Assembled RTF ARRIS EV800 Goggles" is in sale since Saturday, December 10, 2016. This item is in the category "Toys & Hobbies\Radio Control & Control Line\RC Model Vehicles & Kits\Quadcopters & Multicopters". The seller is "hobbywing" and is located in Sichuan. This item can be shipped worldwide.
- Model: 250 fpv racing drone
- Country/Region of Manufacture: China
- Vintage (Y/N): Yes
- Model Grade: Hobby Grade
- Material: Carbon Fiber
- Size Class: 250
- Type: Quadcopter
- Features: First Person Visual (FPV)
- Color: Black
- Required Assembly: Ready to Go/RTR/RTF (All included)
- MPN: CA0057
- Maximum Control Range: 656ft. (200m)
- Fuel Type: Electric
- Brand: ARRIS