We've designed technology into our internal parts to get your wind turbine, hydroelectric, and motor mounted Freedom Series PMG to start-up easier and make more power! This is a high amp model with the new Freedom PMG. It has a 14 magnet rotor inside and. Our skewed stator core for easy turning and. Stainless steel shaft and No Cogging! Now hot dipped galvanized for a 50 year finish!
Up to 1600 watts max output. Starts up in just 3 to 4 mph winds.
Cut in at 6 mph. Here's what you get in the kit. Freedom 9 blade wind turbine. Freedom 3 Sealed PMG (PERMANENT MAGNET GENERATOR) WITH 14 MAGNET ROTOR. 125,000 hours + of rated bearing life.
Freedom PMG has no brushes, Stainless steel rotor shaft, very dependable! Heavy duty hub spacer/stabilizer with slot to fit keyway. Specially designed to channel water away from the PMG housing.
Mounting Bracket and Heavy Duty 2 arms tail assembly. Tail fin measures 29 tall for maximum tracking.
Mounting Bracket Fits on 1.5 schedule #40 or #80 pipe. Comes with 9 black nylon carbon fiber composite blades. Aerodynamically tapered Genuine RAPTOR GENERATION 4 Blades for maximum output. Steel blade hub is 3/16'' thick Zinc Plated. All in One Charge Controller.
Comes prewired for plug and play with. Charge controller with LED volt meter. And rectifier for 3-phase output wind turbine connection. You can also attach additional DC wind turbines and solar panels to the board.
Some of the key features of this hybrid controller are. Dual microprocessor controlled for stability and accuracy. Multiple user changeable settings and trip points for many various system requirements and applications.
You can change the dump point voltage level. End of dump voltage level, and length of time in divert mode when end dump point voltage is reached (between 0 to 999 seconds, or 0 to 999 minutes).
Isolated Electronics Protection - Almost impossible to accidentally connect wind or solar directly to the circuit board. On board relay isolates electronics from back voltage spikes from large 440 amp relay. This is important to get the longest life out of the electronics.
No one else has this! Can be operated at 100% duty cycle conducting surge loads up to 440 amps or 10,000 watts.
Green LED on board lets you know the controller is in dump mode. Plug & Play: Long leads for easy termination to your 12 volt battery or battery bank. Can divert the charging source from the batteries to the load or dump both the batteries along with the charging source. Connect both wind and solar at the same time. Ultra low power consumption, even with the volt meter on (almost negligible). The volt meter can be set to turn off after periods of inactivity.
Missouri Wind and Solar FREEDOM 3 PMG (permanent magnet generator). Our Freedom 3 PMG permanent magnet generator is specifically designed for wind turbine use and can even be used with vertical axis wind turbines (VAWT). The answer is simply the Freedom PMG was designed for wind turbine use and more copper! More copper in the stator core equals more power. Each Freedom PMG rotor contains twice as much copper than any Delco style PMA. 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs and blade sets. Custom hub spacer/stabilizer with keyway and bolts for attaching to Missouri Wind and Solar blade hubs. Zinc plated 14 rare earth neodymium magnet rotor. No brushes to fail or replace.
Arge, heavy duty bearings in front and back. Fits delco bolt patterns and mounts up to our standard mounting bracket.
1 15/16 on center between mounting holes. Products may be slightly different than the ones pictured. If our supplier runs short of the products shown, we will substitute them for the same quality or better.
The seller is "missouriwind" and is located in Seymour, Missouri. This item can be shipped worldwide.
- Color: Black
- Rated Wind Speed: 6 MPH
- Modified Item: No
- MPN: FREEDOM_III_G4_9B_BLACK-3PALL_IN_ONE_DIG_12V
- Number of Blades: 9
- Blade Material: Carbon Fiber
- Rotor Diameter: 61 Inches
- Custom Bundle: Yes
- ISBN: Does not apply
- UPC: Does not apply
- Type: Wind Turbine Generator
- Wattage: 1600 Watts
- Wind Turbine Blade Material: Carbon Fiber Composite
- Bundle Listing: Yes
- Current Type: AC
- System Configuration: Off-Grid
- Brand: Missouri Wind and Solar
- Axis Orientation: Horizontal
- Application: Agriculture/Farming
- Wind Turbine Blade Color: Black
- Resistance Properties: Dust Resistant
- Non-Domestic Product: No
- EAN: Does not apply
- Bundle Description: Includes wind turbine blades, blade hub, locking collar, zinc plated yaw bearing, galvanized mounting bracket, clamps, galvanized tail arms and tail fin, and the nuts and bolts for assembly.